$ sudo smartctl -x /dev/sda
smartctl 6.2 2013-07-26 r3841 [i686-linux-3.12.6-200.fc19.i686.PAE] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 7200.4
Device Model: ST9500420AS
Serial Number: 5VJ68AY2
LU WWN Device Id: 5 000c50 02a34d469
Firmware Version: 0002SDM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Fri Jan 17 07:49:52 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is: 208 (intermediate), recommended: 208
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unknown
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 107) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 085 074 006 - 243348742
3 Spin_Up_Time PO---- 100 100 085 - 0
4 Start_Stop_Count -O--CK 100 100 020 - 96
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
7 Seek_Error_Rate POSR-- 084 060 030 - 238612361
9 Power_On_Hours -O--CK 087 087 000 - 11535
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 100 100 020 - 96
184 End-to-End_Error -O--CK 100 100 099 - 0
187 Reported_Uncorrect -O--CK 001 001 000 - 3765
188 Command_Timeout -O--CK 100 099 000 - 4295032839
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 064 050 045 - 36 (Min/Max 33/43)
191 G-Sense_Error_Rate -O--CK 100 100 000 - 6
192 Power-Off_Retract_Count -O--CK 100 100 000 - 51
193 Load_Cycle_Count -O--CK 097 097 000 - 7794
194 Temperature_Celsius -O---K 036 050 000 - 36 (0 21 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 046 044 000 - 243348742
197 Current_Pending_Sector -O--C- 100 100 000 - 8
198 Offline_Uncorrectable ----C- 100 100 000 - 8
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
240 Head_Flying_Hours ------ 100 253 000 - 132680129719553
241 Total_LBAs_Written ------ 100 253 000 - 2525013242
242 Total_LBAs_Read ------ 100 253 000 - 2162196433
254 Free_Fall_Sensor -O--CK 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 NCQ Command Error log
0x11 GPL,SL R/O 1 SATA Phy Event Counters
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL VS 2248 Device vendor specific log
0xa8 GPL,SL VS 65 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xb0 GPL VS 2864 Device vendor specific log
0xbe-0xbf GPL VS 65535 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 3761 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3761 [0] occurred at disk power-on lifetime: 11535 hours (480 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 7e 00 3d 2c 00 00 Error: UNC at LBA = 0x227e003d2c = 148142832940
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 22 7e 00 3d 28 40 00 18:47:33.157 READ FPDMA QUEUED
60 00 00 00 08 00 36 68 00 f4 18 40 00 18:47:33.157 READ FPDMA QUEUED
60 00 00 00 10 00 36 68 00 f4 00 40 00 18:47:33.157 READ FPDMA QUEUED
60 00 00 00 10 00 36 45 00 f4 f0 40 00 18:47:33.155 READ FPDMA QUEUED
61 00 00 00 28 00 19 f0 00 c1 60 40 00 18:47:33.155 WRITE FPDMA QUEUED
Error 3760 [19] occurred at disk power-on lifetime: 11535 hours (480 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 7e 00 3d 2f 00 00 Error: UNC at LBA = 0x227e003d2f = 148142832943
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 22 7e 00 3d 28 40 00 18:47:22.327 READ FPDMA QUEUED
60 00 00 00 28 00 31 16 00 0b 88 40 00 18:47:21.602 READ FPDMA QUEUED
60 00 00 00 08 00 27 3e 00 50 48 40 00 18:47:21.474 READ FPDMA QUEUED
60 00 00 00 08 00 27 3e 00 50 40 40 00 18:47:21.466 READ FPDMA QUEUED
60 00 00 00 08 00 27 48 00 50 08 40 00 18:47:21.012 READ FPDMA QUEUED
Error 3759 [18] occurred at disk power-on lifetime: 11535 hours (480 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 7e 00 3d 2a 00 00 Error: UNC at LBA = 0x227e003d2a = 148142832938
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 22 7e 00 3d 28 40 00 18:38:24.892 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 18:38:24.891 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 18:38:24.889 IDENTIFY DEVICE
ef 00 03 00 46 00 00 00 00 00 00 a0 00 18:38:24.889 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 00 00 00 00 00 e0 00 18:38:24.889 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 3758 [17] occurred at disk power-on lifetime: 11535 hours (480 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 7e 00 3d 2a 00 00 Error: UNC at LBA = 0x227e003d2a = 148142832938
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 22 7e 00 3d 28 40 00 18:38:22.141 READ FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 a0 00 18:38:21.363 FLUSH CACHE EXT
61 00 00 00 08 00 34 dd 00 23 30 40 00 18:38:21.363 WRITE FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 a0 00 18:38:21.223 FLUSH CACHE EXT
61 00 00 00 60 00 34 dc 00 23 d0 40 00 18:38:21.221 WRITE FPDMA QUEUED
Error 3757 [16] occurred at disk power-on lifetime: 11535 hours (480 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 7e 00 3d 2a 00 00 Error: UNC at LBA = 0x227e003d2a = 148142832938
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 22 7e 00 3d 28 40 00 18:29:26.834 READ FPDMA QUEUED
60 00 00 00 20 00 33 de 00 24 28 40 00 18:29:26.833 READ FPDMA QUEUED
61 00 00 00 48 00 27 c6 00 96 00 40 00 18:29:26.833 WRITE FPDMA QUEUED
61 00 00 00 40 00 28 b0 00 9e 00 40 00 18:29:26.832 WRITE FPDMA QUEUED
61 00 00 01 00 00 28 04 00 a7 00 40 00 18:29:26.832 WRITE FPDMA QUEUED
Error 3756 [15] occurred at disk power-on lifetime: 11535 hours (480 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 7e 00 3d 2a 00 00 Error: UNC at LBA = 0x227e003d2a = 148142832938
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 20 00 33 de 00 24 28 40 00 18:29:24.022 READ FPDMA QUEUED
60 00 00 00 08 00 22 7e 00 3d 28 40 00 18:29:24.021 READ FPDMA QUEUED
60 00 00 00 20 00 33 de 00 24 08 40 00 18:29:24.021 READ FPDMA QUEUED
60 00 00 00 20 00 33 dd 00 24 e8 40 00 18:29:24.021 READ FPDMA QUEUED
60 00 00 00 20 00 33 dd 00 24 c8 40 00 18:29:24.020 READ FPDMA QUEUED
Error 3755 [14] occurred at disk power-on lifetime: 11534 hours (480 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 7e 00 3d 27 00 00 Error: UNC at LBA = 0x227e003d27 = 148142832935
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 37 b6 00 1f 28 40 00 18:20:24.838 READ FPDMA QUEUED
60 00 00 00 68 00 37 b5 00 1f b8 40 00 18:20:24.837 READ FPDMA QUEUED
60 00 00 00 08 00 22 7e 00 3d 20 40 00 18:20:24.834 READ FPDMA QUEUED
27 00 00 00 00 00 00 00 00 00 00 e0 00 18:20:24.833 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 00 00 00 00 00 a0 00 18:20:24.810 IDENTIFY DEVICE
Error 3754 [13] occurred at disk power-on lifetime: 11534 hours (480 days + 14 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 7e 00 3d 27 00 00 Error: UNC at LBA = 0x227e003d27 = 148142832935
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 08 00 22 7e 00 3d 20 40 00 18:20:22.088 READ FPDMA QUEUED
60 00 00 00 08 00 27 4b 00 50 08 40 00 18:20:20.964 READ FPDMA QUEUED
60 00 00 00 08 00 27 4b 00 50 00 40 00 18:20:20.956 READ FPDMA QUEUED
60 00 00 00 08 00 27 49 00 50 38 40 00 18:20:20.948 READ FPDMA QUEUED
60 00 00 00 20 00 26 5f 00 8f 88 40 00 18:20:17.473 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed: read failure 90% 11528 574443398
# 2 Extended offline Completed: read failure 90% 11528 574443398
# 3 Extended offline Completed: read failure 90% 11528 574443398
# 4 Short offline Completed: read failure 90% 11528 574443398
# 5 Short offline Aborted by host 90% 11526 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 36 Celsius
Power Cycle Min/Max Temperature: 33/43 Celsius
Lifetime Min/Max Temperature: 21/50 Celsius
Lifetime Average Temperature: 39 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 14/55 Celsius
Min/Max Temperature Limit: 10/60 Celsius
Temperature History Size (Index): 128 (87)
Index Estimated Time Temperature Celsius
88 2014-01-17 05:42 37 ******************
... ..( 6 skipped). .. ******************
95 2014-01-17 05:49 37 ******************
96 2014-01-17 05:50 36 *****************
97 2014-01-17 05:51 37 ******************
98 2014-01-17 05:52 36 *****************
99 2014-01-17 05:53 36 *****************
100 2014-01-17 05:54 36 *****************
101 2014-01-17 05:55 37 ******************
... ..( 5 skipped). .. ******************
107 2014-01-17 06:01 37 ******************
108 2014-01-17 06:02 36 *****************
109 2014-01-17 06:03 37 ******************
... ..( 12 skipped). .. ******************
122 2014-01-17 06:16 37 ******************
123 2014-01-17 06:17 36 *****************
... ..( 28 skipped). .. *****************
24 2014-01-17 06:46 36 *****************
25 2014-01-17 06:47 37 ******************
... ..( 30 skipped). .. ******************
56 2014-01-17 07:18 37 ******************
57 2014-01-17 07:19 36 *****************
... ..( 20 skipped). .. *****************
78 2014-01-17 07:40 36 *****************
79 2014-01-17 07:41 35 ****************
80 2014-01-17 07:42 36 *****************
81 2014-01-17 07:43 36 *****************
82 2014-01-17 07:44 35 ****************
83 2014-01-17 07:45 36 *****************
... ..( 3 skipped). .. *****************
87 2014-01-17 07:49 36 *****************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS