$ sudo smartctl -x /dev/sda
smartctl 6.2 2013-07-26 r3841 [i686-linux-3.12.6-200.fc19.i686.PAE] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 7200.4
Device Model: ST9500420AS
Serial Number: 5VJ68AY2
LU WWN Device Id: 5 000c50 02a34d469
Firmware Version: 0002SDM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Thu Jan 16 22:34:40 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM level is: 208 (intermediate), recommended: 208
APM level is: 128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unknown
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 107) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 081 079 006 - 16583263
3 Spin_Up_Time PO---- 100 100 085 - 0
4 Start_Stop_Count -O--CK 100 100 020 - 96
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
7 Seek_Error_Rate POSR-- 084 060 030 - 238415653
9 Power_On_Hours -O--CK 087 087 000 - 11526
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 100 100 020 - 96
184 End-to-End_Error -O--CK 100 100 099 - 0
187 Reported_Uncorrect -O--CK 001 001 000 - 1195
188 Command_Timeout -O--CK 100 099 000 - 4295032839
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 059 050 045 - 41 (Min/Max 33/41)
191 G-Sense_Error_Rate -O--CK 100 100 000 - 6
192 Power-Off_Retract_Count -O--CK 100 100 000 - 51
193 Load_Cycle_Count -O--CK 097 097 000 - 7756
194 Temperature_Celsius -O---K 041 050 000 - 41 (0 21 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 045 044 000 - 16583263
197 Current_Pending_Sector -O--C- 100 100 000 - 6
198 Offline_Uncorrectable ----C- 100 100 000 - 6
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
240 Head_Flying_Hours ------ 100 253 000 - 275839979629816
241 Total_LBAs_Written ------ 100 253 000 - 1781489951
242 Total_LBAs_Read ------ 100 253 000 - 695406064
254 Free_Fall_Sensor -O--CK 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 NCQ Command Error log
0x11 GPL,SL R/O 1 SATA Phy Event Counters
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL VS 2248 Device vendor specific log
0xa8 GPL,SL VS 65 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xb0 GPL VS 2864 Device vendor specific log
0xbe-0xbf GPL VS 65535 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 1200 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1200 [19] occurred at disk power-on lifetime: 11526 hours (480 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 4f 00 3d 86 00 00 Error: UNC at LBA = 0x224f003d86 = 147354303878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 28 00 31 32 00 6e 78 40 00 09:38:03.296 READ FPDMA QUEUED
60 00 00 00 08 00 22 4f 00 3d 80 40 00 09:38:03.294 READ FPDMA QUEUED
61 00 00 00 10 00 37 b0 00 21 70 40 00 09:38:03.293 WRITE FPDMA QUEUED
61 00 00 00 58 00 1a 33 00 29 28 40 00 09:38:03.293 WRITE FPDMA QUEUED
ea 00 00 00 00 00 00 00 00 00 00 a0 00 09:38:03.293 FLUSH CACHE EXT
Error 1199 [18] occurred at disk power-on lifetime: 11526 hours (480 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 4f 00 3d 86 00 00 Error: WP at LBA = 0x224f003d86 = 147354303878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 00 08 00 34 05 00 24 d8 40 00 09:38:00.385 WRITE FPDMA QUEUED
60 00 00 00 48 00 31 db 00 fb d0 40 00 09:38:00.385 READ FPDMA QUEUED
60 00 00 00 20 00 31 db 00 fb 98 40 00 09:38:00.385 READ FPDMA QUEUED
60 00 00 00 08 00 22 4f 00 3d 80 40 00 09:38:00.384 READ FPDMA QUEUED
60 00 00 01 08 00 10 c0 00 62 00 40 00 09:38:00.383 READ FPDMA QUEUED
Error 1198 [17] occurred at disk power-on lifetime: 11526 hours (480 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 4f 00 3d 86 00 00 Error: WP at LBA = 0x224f003d86 = 147354303878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 00 10 00 37 b0 00 21 60 40 00 09:37:57.428 WRITE FPDMA QUEUED
60 00 00 00 18 00 33 aa 00 fd 60 40 00 09:37:57.427 READ FPDMA QUEUED
60 00 00 00 08 00 22 4f 00 3d 80 40 00 09:37:57.426 READ FPDMA QUEUED
61 00 00 00 08 00 1a 33 00 29 20 40 00 09:37:57.426 WRITE FPDMA QUEUED
60 00 00 00 28 00 31 db 00 fb 70 40 00 09:37:57.424 READ FPDMA QUEUED
Error 1197 [16] occurred at disk power-on lifetime: 11526 hours (480 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 4f 00 3d 86 00 00 Error: UNC at LBA = 0x224f003d86 = 147354303878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 01 28 00 34 b4 00 30 d0 40 00 09:37:54.457 READ FPDMA QUEUED
60 00 00 00 08 00 22 4f 00 3d 80 40 00 09:37:54.455 READ FPDMA QUEUED
61 00 00 00 10 00 37 b0 00 21 58 40 00 09:37:54.455 WRITE FPDMA QUEUED
61 00 00 00 10 00 28 0c 00 df 00 40 00 09:37:54.454 WRITE FPDMA QUEUED
61 00 00 00 08 00 28 5b 00 09 10 40 00 09:37:54.454 WRITE FPDMA QUEUED
Error 1196 [15] occurred at disk power-on lifetime: 11526 hours (480 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 4f 00 3d 86 00 00 Error: WP at LBA = 0x224f003d86 = 147354303878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 00 08 00 34 05 00 24 68 40 00 09:37:51.484 WRITE FPDMA QUEUED
60 00 00 02 00 00 34 b2 00 30 d0 40 00 09:37:51.483 READ FPDMA QUEUED
60 00 00 00 20 00 31 d7 00 fb f8 40 00 09:37:51.483 READ FPDMA QUEUED
60 00 00 00 08 00 22 4f 00 3d 80 40 00 09:37:51.481 READ FPDMA QUEUED
61 00 00 00 10 00 37 b0 00 21 50 40 00 09:37:51.481 WRITE FPDMA QUEUED
Error 1195 [14] occurred at disk power-on lifetime: 11526 hours (480 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 4f 00 3d 86 00 00 Error: WP at LBA = 0x224f003d86 = 147354303878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 00 08 00 1a 32 00 29 e0 40 00 09:37:48.503 WRITE FPDMA QUEUED
60 00 00 00 c0 00 34 b2 00 30 10 40 00 09:37:48.502 READ FPDMA QUEUED
60 00 00 00 08 00 22 4f 00 3d 80 40 00 09:37:48.501 READ FPDMA QUEUED
61 00 00 00 10 00 37 b0 00 21 48 40 00 09:37:48.500 WRITE FPDMA QUEUED
61 00 00 00 08 00 34 35 00 37 e0 40 00 09:37:48.500 WRITE FPDMA QUEUED
Error 1194 [13] occurred at disk power-on lifetime: 11526 hours (480 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 4f 00 3d 86 00 00 Error: UNC at LBA = 0x224f003d86 = 147354303878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
60 00 00 00 20 00 34 b1 00 30 f0 40 00 09:37:45.570 READ FPDMA QUEUED
60 00 00 00 28 00 31 d7 00 fb d0 40 00 09:37:45.569 READ FPDMA QUEUED
60 00 00 00 08 00 22 4f 00 3d 80 40 00 09:37:45.568 READ FPDMA QUEUED
61 00 00 00 10 00 37 b0 00 21 40 40 00 09:37:45.567 WRITE FPDMA QUEUED
61 00 00 00 10 00 1f 81 00 8d 20 40 00 09:37:45.567 WRITE FPDMA QUEUED
Error 1193 [12] occurred at disk power-on lifetime: 11526 hours (480 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 22 4f 00 3d 86 00 00 Error: WP at LBA = 0x224f003d86 = 147354303878
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 00 08 00 34 05 00 24 28 40 00 09:37:42.561 WRITE FPDMA QUEUED
60 00 00 00 38 00 37 db 00 06 38 40 00 09:37:42.560 READ FPDMA QUEUED
60 00 00 00 18 00 37 db 00 06 18 40 00 09:37:42.560 READ FPDMA QUEUED
60 00 00 00 08 00 37 db 00 06 08 40 00 09:37:42.560 READ FPDMA QUEUED
60 00 00 00 20 00 37 da 00 06 e0 40 00 09:37:42.559 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 41 Celsius
Power Cycle Min/Max Temperature: 33/41 Celsius
Lifetime Min/Max Temperature: 21/50 Celsius
Lifetime Average Temperature: 39 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 14/55 Celsius
Min/Max Temperature Limit: 10/60 Celsius
Temperature History Size (Index): 128 (48)
Index Estimated Time Temperature Celsius
49 2014-01-16 20:28 39 ********************
... ..( 4 skipped). .. ********************
54 2014-01-16 20:33 39 ********************
55 2014-01-16 20:34 38 *******************
... ..( 12 skipped). .. *******************
68 2014-01-16 20:47 38 *******************
69 2014-01-16 20:48 39 ********************
... ..( 7 skipped). .. ********************
77 2014-01-16 20:56 39 ********************
78 2014-01-16 20:57 40 *********************
... ..( 23 skipped). .. *********************
102 2014-01-16 21:21 40 *********************
103 2014-01-16 21:22 39 ********************
... ..( 38 skipped). .. ********************
14 2014-01-16 22:01 39 ********************
15 2014-01-16 22:02 40 *********************
... ..( 18 skipped). .. *********************
34 2014-01-16 22:21 40 *********************
35 2014-01-16 22:22 41 **********************
... ..( 12 skipped). .. **********************
48 2014-01-16 22:35 41 **********************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
Device Statistics (GP Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS